WorkShield Overview

The sections below describe WorkShield, providing an overview of the artwork carrying case’s key features

WorkShield in outline

WorkShield consists of three main parts – the board, the slipcase and the holders (as highlighted in bold on the photo).

Place the artwork on the board and hold it in position with the holders. Then slide the board into the slipcase, protecting the artwork.

The angled beam runs along the bottom of the board, functioning as a long version of a holder.

The board’s top beam carries the twist-locks, which fasten the board and slipcase together.

The slipcase includes a handle and also eyelets to allow a shoulder strap to be fitted.

Slipcase, board and holders are made from light, rigid, fluted polypropylene, which can be easily recycled.

What can WorkShield 4000 carry?

CarriArt WorkShield 4000 can accommodate a single piece of artwork on a standard 20mm deep stretched canvas up to 310x470mm (including common sizes ISO A3, 10×12″ and 12×16″), or a slightly larger board or a slightly smaller box canvas. Where space permits, two or more smaller pieces of artwork may be accommodated by using additional holders.

The overall size of WorkShield 4000 size is 550×530 x65mm (22x21x3″). Each holder measures 80x50x50mm. Maximum recommended canvas or frame depth 40mm (1 1/2″).

Get onboard the board

The WorkShield board is designed to securely carry artwork without damaging its surface.

Rest artwork against the angled beam, which runs along the bottom edge of the board, then place holders around the remaining edges. The slope of the angled beam and the holders prevents artwork from moving vertically or horizontally.

The top beam carries two twist-locks.  (The top beam can also store art materials.)

Once the artwork is secure, the board slides easily into the slipcase where the twist-locks link the board and slipcase together. Then the WorkShield artwork carrying case is good to go!

The photo shows the Workshield 4000 board carrying an A3 canvas, held in place by the angled beam and three holders.

Combine the board with the slipcase

The outer part of WorkShield is a slipcase, which fits over the board, protecting artwork from damage.

A handle on the top edge of the slipcase makes WorkShield easy to carry. Ether side of the handle, two eyelets allow attachment of a shoulder strap.

The photo shows the WorkShield slipcase from below, highlighting the opening which accommodates the board. Note the semi-circular cut-outs, which make it easy to take hold of the board when removing it from the slipcase.

Get a grip on the slipcase handle

Use the handle attached to the top of the slipcase for carrying WorkShield. The handle stands proud of the slipcase and swivels, making WorkShield easy to carry.

Also use the handle to steady the slipcase when removing the board.

 

Strap eyelets and twist-locks

The top edge of the slipcase carries the twist-locks and the strap eyelets.

The twist-locks secure the board in place within the slipcase. The board carries the main part of the twist-locks, while the slipcase carries the twist-lock receptacles. When slipped into the slipcase, the board aligns seamlessly. Then, to fasten the board and slipcase together, simply turn the twist-lock tab though 90 degrees.

The strap eyelets fixed to the top of the slipcase, make it easy to add a strap to the WorkShield artwork carrying case (and to remove it as well).

Angled beam and side buttresses

The angled beam runs along the bottom edge of the board. It has the same sloping profile as the holders, keeping one side of the artwork firmly in place without damaging its surface.

At either end of the angled beam, thin buttresses run from the top of the angled beam down to the board. The buttresses help prevent the angled beam from catching on the top edge of the slipcase when joining the two together.

The buttresses have two other uses. Firstly, one edge of your artwork rests against one of the buttresses, ensuring your artwork stays on the board. Secondly, the buttresses support the angled beam, improving its rigidity.

Built-in storage

A hollow beam runs along the top of the board. This makes the WorkShield artwork carrying case also ideal for transporting art materials.

Pack items such as paint brushes and tubes of paint into the upper beam. Then slide the board into the slipcase, and your materials are safely stored away.

Thinner at the top

The board narrows slightly around the top beam.

This makes it easier to pair the board with the slipcase. (While ensuring there is a good fit between the two when the board is inside the slipcase.)

Which way is up?

Use the orange guidance triangle printed on the back of the angled beam, to ensure the board is removed from the slipcase with artwork the right way up.

Simply keep the triangle pointing upwards to avoid having problems when separating the board and slipcase!

Shopping Basket